View HI-8191PSMF_5815512.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

general description the hi-8190 is a quad analog cmos switch fabricated with sili- con-on-insulator (soi) technology for latch-up free operation and maximum switch isolation. the switch voltages can range from bipolar each switch is designed using back to back high voltage transistors. switch transistors are symmetrical and conduct equally well in either direction. signal range can run the full rails. off leakages are very low (1 na typi- cal) and charge injection is less than 3 pc. switch esd toler- ance is greater than 4 kv. the off state is achieved first before any on condition is ap- plied. switching times with a 3.3v vlogic supply are typically 35 ns to the on state and 20 ns to the off state. (-40c to +85c) and extended (-55c to +125c) temperature range options. 3.3v to 15v or single ended from 3.3v to 15v. the logic supply can range from 3.3v to 5.0v. the hi-8190 pro- vides four each normally open switches when the switch control inputs are low. the hi-8191 provides four each normally closed switches when the switch control inputs are low. the hi- 8192 provides a combination of two normally on and two nor- mally off switches. the limits of the operating range are de- fined by the v+/v- bias voltage. on-resistance of each switch depends upon only the vlogic selection. at 5v, r ranges from 10 to 17 while at 3.3v sup- ply r ranges from 10 to 22 industry-standard plastic package options include 16-pin tssop, so, dip and 16-pin qfn. ceramic packaging is avail- able on request. all three products are offered in both industrial on on features 3.3v to 15v cmos analog switches low ron: 12 to 15 typical robust cmos silicon-on-insulator (soi) technology soi switch isolation with 1na typical off leakage superior esd protection > 4kv hbm fast switching time with break-before-make low power extended temperature range (-55c to +125c) pin configurations (top views) october 2011 (ds8190 rev. new) 10/11 hi-8190, hi-8191, hi-8192 12 , quad, spst, 3.3v / 5.0v compatible analog switch 16 s1a 15 in1 14 in2 13 s2a s1b 1 v- 2 gnd 3 s4b 4 12 s2b 11 v+ 10 vlogic 9 s3b s4a 5 in4 6 in3 7 s3a 8 16-pin 5mm x 5mm chip-scale package hi-8190pcx applications data bus isolation sample-and-hold circuits test equipment communications systems battery operated systems pbx, pabx audio signal routing data acquisition systems xdsl modems avionics in1 1 s1a 2 s1b 3 v- 4 gnd 5 s4b 6 s4a 7 in4 8 16 in2 15 s2a 14 s2b 13 v+ 12 vlogic 11 s3b 10 s3a 9 in3 16-pin so or dip package hi-8190psx, hi-8190pdx product options part type in1 switch 1 in2 switch 2 in3 switch 3 in4 switch 4 hi-8190 0 open 0 open 0 open 0 open 1 closed 1 closed 1 closed 1 closed hi-8191 0 closed 0 closed 0 closed 0 closed 1 open 1 open 1 open 1 open hi-8192 0 open 0 closed 0 closed 0 open 1 closed 1 open 1 open 1 closed holt integrated circuits www.holtic.com
hi-8190, hi-8191, hi-8192 signal function description in1 logic input hi-8190 and hi-8192 are normally open when input low s1a switch node switch 1 node s1b switch node switch 1 node v- supply negative supply for bipolar configuration. gnd for unipolar use gnd supply reference ground s4b switch node switch 4 node s4a switch node switch 4 node in4 logic input hi-8190 and hi-8192 are normally open when input low in3 logic input hi-8191 and hi-8192 are normally closed when input low s3a switch node switch 3 node s3b switch node switch 3 node vlogic supply 3.3v or 5.0v logic supply v+ supply positive supply for bipolar and unipolar configurations s2b switch node switch 2 node s1b switch node switch 2 node in2 logic input hi-8191 and hi-8192 are normally closed when input low pin descriptions -15v -10v -5v 0v 5v 10v 15v 8 10 12 14 16 18 20 22 24 v switch r on v switch r on -15v -10v -5v 0v 5v 10v 15v 8 10 12 14 16 18 20 22 24 v switch r on -15v -10v -5v 0v 5v 10v 15v v switch r on typical r as a function of v (10ma switch current) v=5v on switch logic and temperature typical r as a function of v and v (10ma switch current, on logic switch 25c) v = 3.3v logic v = 5.0v logic t = +125c t = +25c t = -55c holt integrated circuits 2
electrical characteristics v+ = 15v, v- = -15v, gnd = 0v. operating temperature range (unless otherwise noted). v = 3.3v v = 5.0v parameter conditions figure unit logic logic symbol switch parameters switch signal range v -15 +15 v switch resistance r 25c, 10ma 1 10 22 10 17 -55c to +125c, 10ma 1 8 26 8 20 leakage i switch voltage 2 5 5 na logic inputs input high voltage v 70 70 %v input low voltage v 30 30 %v input current i v = 0v or v =vlogic -0.5 0.5 -0.5 0.5 supply vlogic current i any state 0.5 0.5 v+ current i any state 0.5 0.5 v- current i any state -0.5 -0.5 dynamic parameters turn on time t v+/v- = 10v, 25c 3 55 35 ns turn off time t break-before-make time t 10v signal, 25c 4 8 8 ns 10v signal, -55c to +125c 4 4 4 ns charge injection q v =0v, r =0 25c 5 4 4 pc off isolation r f = 1 mhz, 25c 6 65 65 db crosstalk c 25c 7 90 90 db capacitance c switch off, 25c 8 5 5 pf c switch on, 25c 9 20 20 pf min typ max min typ max range on swleak ih logic il logic in in in dd1 dd2 ee on off d ss r r off on | | 15v, 25c |i | switch voltage 15v, 125 2 20 20 na |i | switch voltage 15v, -55c 2 150 150 na a a a a v = 10v, -55c to +125c 3 75 55 ns v+/v- = 10v, 25c 3 35 20 ns v = 10v, -55c to +125c 3 40 25 ns f = 1 mhz, swleak swleak s s hi-8190, hi-8191, hi-8192 note: stresses above those listed under "absolute maximum ratings" may cause permanent damage to the device. these are stress ratings only. functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not imp lied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. absolute maximum ratings continuous power dissipation (ta=70c): so package (derate 6.7mw/c above 70c)...................696mw plastic dip (derate 10.53 mw/c above 70c) .................842mw thin qfn (derate 21.3mw/c above 70c) ...................1702mw storage temperature range: ......................................-65c to +150c soldering temperature: (ceramic)......................60 sec. at +300c (plastic - leads).............10 sec. at +280c (plastic - body) .....................+260c max. supply voltage, v+: ............................................................................16.5v supply voltage, v-:.............................................................................-16.5v supply volgate, v .........................................................................5.5v switch current (either direction) peak switch current (1 ms pulse, 10% duty cycle max.)..................200ma digital input voltage (in1-4):..................................... logic :.........................................................50ma -0.3v to v + 0.3v operating temperature range: (industrial)..........................-40c to +85c (hi-temp) ........................-55c to +125c maximum junction temperature ........................................................175c logic (voltages referenced to gnd = 0v) holt integrated circuits 3
holt integrated circuits 4 figure 1 - on resistance figure 3. switching times v (hi-8191) in v out v (hi-8190) in 50% 50% t on t off 50% 90% test circuits hi-8190, hi-8191, hi-8192 + - v s i ds r=v/i on 1 ds v 1 figure 2 - off leakage + - v s i (off) s v d aa - + i (off) d + - v s 35pf +5v +15v -15v v logic v + v- gnd 0.1 f 0.1 f 0.1 f v out sa sb sa sb sa sb in 50% 50% figure 4. break-before-make time delay (hi-8192) 35pf +5v +15v -15v v logic v + v- gnd 0.1 f 0.1 f 0.1 f v out1 s1a s1b in s2a s2b v s1 v s2 v out2 35pf v in v out1 5v 0v 50% 50% v out2 50% 90% t d t d 50% 90%
holt integrated circuits 5 hi-8190, hi-8191, hi-8192 figure 5. charge injection v in v out + - v s c 10nf l +5v +15v -15v v logic v + v- gnd v out sa sb in v out qc inj = l x ut v o r s v s +5v +15v -15v v logic v + v- gnd 0.1 f 0.1 f 0.1 f v out sa sb in figure 6 - off isolation v s +5v +15v -15v v logic v + v- gnd 0.1 f 0.1 f 0.1 f sa1 sb1 in1 figure 7 - channel-to-channel crosstalk v out sa2 sb2 in2 nc v s +5v +15v -15v v logic v + v- gnd 0.1 f 0.1 f 0.1 f sa sb in figure 8 - off capacitance capacitance meter f=1mhz +5v +15v -15v v logic v + v- gnd 0.1 f 0.1 f 0.1 f sa sb in figure 9 - on capacitance capacitance meter f=1mhz
holt integrated circuits 6 ordering information hi - 819x xx x x temperature range flow burn in -40c to +85c -55c to +125c no yes i m -55c to +125c no t part number t i m package description 16 pin plasti c5x5mm chip scale (16pcs1) (no m-flow) part number pc 16 pin plastic narrow body soic (16hn) ps pd lead finish part number 100% matte tin (pb-free, rohs compliant) f tin / lead (sn / pb) solder blank 16 pin plastic dip (16p) function quad switch, normally open part number 8190 quad switch, normally closed 8191 8192 quad switch, two normally open, two normally closed hi-8190, hi-8191, hi-8192
p/n rev date description of change ds8190 new 10/26/11 initial release revision history holt integrated circuits 7 hi-8190, hi-8191, hi-8192
hi-8190 package dimensions 16-pin plastic chip-scale package millimeters package type: 16pcs1 bsc = ?basic spacing between centers? is theoretical true position dimension and has no tolerance. (jedec standard 95) top view bottom view electrically isolated metal heat sink on bottom of package connect to any ground or power plane for optimum thermal dissipation 16-pin plastic small outline (soic) - nb (narrow body) inches (millimeters) package type: 16hn bsc = ?basic spacing between centers? is theoretical true position dimension and has no tolerance. (jedec standard 95) 0
to 8
detail a .0069 .0029 (.176 .074) .033 .017 (.838 .432) .061 .007 (1.549 .178) .0165 .003 (.419 .089) .390 .004 (9.90 .10) .236 .008 (5.99 .20) .0087 .0012 (.220 .029) see detail a .1525 .0025 (3.87 .06) top view .050 (1.27) bsc 5.00 0.05 (0.197 0.002) 5.00 0.05 (0.197 0.002) 3.38 0.05 (0.133 0.002) 3.38 0.05 (0.133 0.002) 0.75 0.05 (0.03 0.002) 0.025 0.025 (0.001 0.001) 0.203 (0.008) ref. 0.80 (0.031) bsc 0.30 0.012 0.05 ( 0.002) .50 0.05 (0.020 0.002) 0.20 (0.008) min. holt integrated circuits 8
holt integrated circuits 9 hi-8190 package dimensions inches (millimeters) package type: 16-pin plastic dip 16p 0.745 (18.923) 0.810 (20.574) 0.240 (6.096) 0.260 (6.604) 0.300 (7.620) 0.370 (9.398) 0.125 (3.175) 0.150 (3.810) 0.015 (0.381) 0.035 (0.889) 0.100 (2.54) bsc. 0.045 (1.143) 0.065 (1.651) 0.015 (0.381) 0.023 (0.584) 0.120 (3.048) 0.150 (3.810) 0.290 (7.366) 0.310 (7.874) 0.008 (0.203) 0.015 (0.381)

▲Up To Search▲

Price & Availability of HI-8191PSMF

	To Download HI-8191PSMF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .